Naar inhoud springen

Bestand:BWR Mark I Containment, diagram.png

Pagina-inhoud wordt niet ondersteund in andere talen.
Uit Wikivoyage

Oorspronkelijk bestand(826 × 852 pixels, bestandsgrootte: 80 kB, MIME-type: image/png)

Beschrijving

Beschrijving
English: Diagram of a typical Boiling water reactor (BWR) Mark I Concrete Containment with Steel Torus, as used in the BWR/1, BWR/2, BWR/3 and some BWR/4 model reactors.
Français : Diagrame/coupe d'un réacteur à eau bouillante (REB) typique de type Mark I à enceinte de confinement en béton avec tore d'acier sous-jacent, tel qu'utilisé dans les réacteurs de type REB/1, REB/2, REB/3 et certains REB/4.
Datum Source published July 2006, but this diagram may predate this
Bron Page 15 (pdf: 40), Containment Integrity Research at Sandia National Laboratories - An Overview, Manuscript completed: March 2006, Published: July 2006, id: NUREG/CR-6906 and SAND2006-2274P [1] - Prepared by Sandia National Laboratories for the U.S. Nuclear Regulatory Commission, Job Code Y6757
Auteur Sandia National Laboratories
Andere versies

The two diagrams on the same page are labeled: Figure 5 Typical BWR Mark I Concrete Containment with Steel Torus.

The report text describing the diagrams, on page 10 (pdf 35) is:

BWR Mark I

The Mark I is a pressure suppression containment (Figure 5), which allows the containment to be smaller in volume. The containment is divided into the drywell containing the reactor vessel and the wetwell (torus) containing the suppression pool. The containments are constructed of either concrete or steel. The water in the suppression pool acts as an energy absorbing medium in the event of an accident. If a LOCA [loss of coolant accident] occurs, steam flows from the drywell through a set of vent lines and downcomers into the suppression pool, where the steam is condensed. Steam can also be released from the reactor vessel through the safety relief valves and associated piping directly into the suppression pool. In the event that the pressure in the wetwell exceeds the pressure in the drywell, vacuum breakers are provided that equalize the pressure. Mark I containments are equipped with lines connected to the wetwell that can be used to vent the containment if the pressure becomes too high.

Licentie

Public domain
Dit werk bevindt zich in het publieke domein in de Verenigde Staten omdat het is vervaardigd door een ambtenaar van de Amerikaanse federale overheid tijdens de uitoefening van zijn functie, en het daarmee volgens Titel 17, Hoofdstuk 1, Sectie 105 van de United States Code [Engelstalige link] een werk van de Amerikaanse federale overheid [Engelstalige link] is. Nota bene: Het bovenstaande is alleen van toepassing op werken van de federale overheid of een van haar onderdelen, en niet op werken van een afzonderlijk(e) Staat, Territorium, Commonwealth, County, Gemeente, of enig andere bestuurlijke eenheid. Dit sjabloon is ook niet van toepassing op ontwerpen voor postzegels, door de United States Postal Service openbaar gemaakt sinds 1978 [Engelstalige link]. Zie Art. 206.02(b) van "Compendium II: Copyright Office Practices" (Engelstalig).

Aantekeningen
InfoField
Deze afbeelding is aangetekend: Bekijk de aantekeningen op Commons

Bijschriften

Beschrijf in één regel wat dit bestand voorstelt

Items getoond in dit bestand

beeldt af

image/png

e7f4e2b8f4c86ff25fbf0a78968eb17da47b9584

82.271 byte

852 pixel

826 pixel

Bestandsgeschiedenis

Klik op een datum/tijd om het bestand te zien zoals het destijds was.

Datum/tijdMiniatuurAfmetingenGebruikerOpmerking
huidige versie13 mrt 2011 21:03Miniatuurafbeelding voor de versie van 13 mrt 2011 21:03826 × 852 (80 kB)Rwendland{{Information |Description ={{en|1=Diagram of a typical Boiling water reactor (BWR) Mark I Concrete Containment with Steel Torus, as used in the BWR/1, BWR/2, BWR/3 and some BWR/4 model reactors.}} |Source =Containment Integrity Research at San

Geen enkele pagina gebruikt dit bestand.

Globaal bestandsgebruik

De volgende andere wiki's gebruiken dit bestand: